pacman -Sy lm_sensors
2. Редактируем /etc/rc.conf, в загружаемые модули добавляем (MODULES):
i2c-nforce2 i2c-isa eeprom it87
3. В /etc/rc.local добавляем строчку
sensors -s
4. Открываем /etc/modprobe.conf, добавляем:
Код: Выделить всё
# I2C module options
alias char-major-89 i2c-dev5. Сохраняем патч ниже в файл nforce4-sensors.diff
Код: Выделить всё
--- sensors.conf.orig 2005-10-03 03:38:49.000000000 +1100
+++ sensors.conf 2006-06-18 23:13:52.000000000 +1100
@@ -1504,7 +1504,7 @@
# Voltage monitors as advised in the It8705 data sheet
- label in0 "VCore 1"
+ label in0 "VCore"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
@@ -1517,6 +1517,11 @@
# vid is not monitored by IT8705F
# comment out if you have IT8712
ignore vid
+ ignore in1
+ ignore in5
+ ignore in6
+ ignore in7
+ ignore in8
# Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
# to report the VCORE voltage approximately 0.05V higher than the board's
@@ -1524,10 +1529,11 @@
# the next line should bring the readings in line with the BIOS' ones in
# this case.
# compute in0 -0.05+@ , @+0.05
+compute in0 0.03+@ , @-0.03
# If 3.3V reads 2X too high (Soyo Dragon and Asus A7V8X-X, for example),
# comment out following line.
- compute in2 2*@ , @/2
+ #compute in2 2*@ , @/2
#
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10) +1)*@ , @/((30/10) +1)
@@ -1560,6 +1566,8 @@
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
+ #set in0_min 1.2
+ #set in0_max 1.8
set in1_min 2.4
set in1_max 2.6
set in2_min 3.3 * 0.95
@@ -1591,12 +1599,14 @@
# (see ignore statement right below).
label temp1 "M/B Temp"
- set temp1_over 40
+ #set temp1_over 40
+ set temp1_over 45
set temp1_low 15
label temp2 "CPU Temp"
- set temp2_over 45
+ #set temp2_over 45
+ set temp2_over 50
set temp2_low 15
-# ignore temp3
+ ignore temp3
label temp3 "Temp3"
set temp3_over 45
set temp3_low 15
@@ -1618,6 +1628,9 @@
set fan2_min 3000
# ignore fan3
set fan3_min 3000
+ label fan1 "CPU fan"
+ label fan2 "CHA fan"
+ label fan3 "CHIP fan"
# The following is for the Inside Technologies 786LCD which uses either a
# IT8705F or a SIS950 for monitoring with the SIS630.помещаем его в каталог /etc и делаем
patch -p0 < nforce4-sensors.diff
6. Вызываем sensors и любуемся
ЗЫ написано по памяти на работе, дома будет доделано
)))))